Step 1: Create a VPC

Scenarios

A VPC provides an isolated virtual network for ECSs. You can configure and manage the network as required.

Create a VPC by following the procedure provided in this section. Then, create subnets, security groups, and assign EIPs by following the procedure provided in subsequent sections based on your actual network requirements.

Procedure

  1. Log in to the management console.

  2. Click image1 in the upper left corner and select the desired region and project.

  3. On the console homepage, under Network, click Virtual Private Cloud.

  4. Click Create VPC.

  5. On the Create VPC page, set parameters as prompted.

    A default subnet will be created together with a VPC and you can also click Add Subnet to create more subnets for the VPC.

    Table 1 VPC parameter descriptions

    Category

    Parameter

    Description

    Example Value

    Basic Information

    Region

    Regions are geographic areas that are physically isolated from each other. The networks inside different regions are not connected to each other, so resources cannot be shared across different regions. For lower network latency and faster access to your resources, select the region nearest you.

    ec-ch2

    Basic Information

    Name

    The VPC name.

    The name can contain a maximum of 64 characters, which may consist of letters, digits, underscores (_), hyphens (-), and periods (.). The name cannot contain spaces.

    VPC-001

    Basic Information

    IPv4 CIDR Block

    The CIDR block of the VPC. The CIDR block of a subnet can be the same as the CIDR block for the VPC (for a single subnet in the VPC) or a subset of the CIDR block for the VPC (for multiple subnets in the VPC).

    The following CIDR blocks are supported:

    10.0.0.0/8-24

    172.16.0.0/12-24

    192.168.0.0/16-24

    192.168.0.0/16

    Basic Information/Advanced Settings

    Tag

    The VPC tag, which consists of a key and value pair. You can add a maximum of 20 tags to each VPC.

    The tag key and value must meet the requirements listed in Table 2.

    • Key: vpc_key1

    • Value: vpc-01

    Basic Information/Advanced Settings

    Description

    Supplementary information about the VPC. This parameter is optional.

    The VPC description can contain a maximum of 255 characters and cannot contain angle brackets (< or >).

    N/A

    Default Subnet

    Name

    The subnet name.

    The name can contain a maximum of 64 characters, which may consist of letters, digits, underscores (_), hyphens (-), and periods (.). The name cannot contain spaces.

    Subnet

    Default Subnet

    IPv4 CIDR Block

    The CIDR block for the subnet. This value must be within the VPC CIDR block.

    192.168.0.0/24

    Default Subnet

    IPv6 CIDR Block

    Specifies whether to set IPv6 CIDR Block to Enable.

    After the IPv6 function is enabled, the system automatically assigns an IPv6 CIDR block to the created subnet. Currently, the IPv6 CIDR block cannot be customized. IPv6 cannot be disabled after the subnet is created.

    -

    Default Subnet

    Associated Route Table

    The default route table to which the subnet will be associated. You can change the route table to a custom route table on the Subnets page.

    Default

    Default Subnet/Advanced Settings

    Gateway

    The gateway address of the subnet.

    192.168.0.1

    Default Subnet/Advanced Settings

    DNS Server Address

    By default, two DNS server addresses are configured. You can change them as required. A maximum of five DNS server addresses can be configured. Multiple IP addresses must be separated using commas (,).

    100.125.x.x

    Default Subnet/Advanced Settings

    NTP Server Address

    The IP address of the NTP server. This parameter is optional.

    You can configure the NTP server IP addresses to be added to the subnet as required. The IP addresses are added in addition to the default NTP server addresses. If this parameter is left empty, no IP address of the NTP server is added.

    A maximum of four IP addresses can be configured. Multiple IP addresses must be separated using commas (,).

    192.168.2.1

    Default Subnet/Advanced Settings

    Tag

    The subnet tag, which consists of a key and value pair. You can add a maximum of 20 tags to each subnet.

    The tag key and value must meet the requirements listed in Table 3.

    • Key: subnet_key1

    • Value: subnet-01

    Table 2 VPC tag key and value requirements

    Parameter

    Requirements

    Example Value

    Key

    • Cannot be left blank.

    • Must be unique for the same VPC and can be the same for different VPCs.

    • Can contain a maximum of 36 characters.

    • Can contain only the following character types:

      • Uppercase letters

      • Lowercase letters

      • Digits

      • Special characters, including hyphens (-) and underscores (_)

    vpc_key1

    Value

    • Can contain a maximum of 43 characters.

    • Can contain only the following character types:

      • Uppercase letters

      • Lowercase letters

      • Digits

      • Special characters, including hyphens (-) and underscores (_)

    vpc-01

    Table 3 Subnet tag key and value requirements

    Parameter

    Requirements

    Example Value

    Key

    • Cannot be left blank.

    • Must be unique for each subnet.

    • Can contain a maximum of 36 characters.

    • Can contain only the following character types:

      • Uppercase letters

      • Lowercase letters

      • Digits

      • Special characters, including hyphens (-) and underscores (_)

    subnet_key1

    Value

    • Can contain a maximum of 43 characters.

    • Can contain only the following character types:

      • Uppercase letters

      • Lowercase letters

      • Digits

      • Special characters, including hyphens (-) and underscores (_)

    subnet-01

  6. Click Create Now.

last updated: 2024-11-08 14:04 UTC - commit: c1342f38aaa052dfe3f75e6032ecaa392e78b7ff